WST-TCP2WG12 TCP/IP to 2CH Wiegand Relay Controller

General Introduction

This controller was developed to interface access control system. It can be a TCP/IP to 2CH Wiegand converter, and also can be a simply TCP/IP network single door access controller. It has 2CH of Wiegand interface, 2CH input interface with two PIN to support push button (manual door open switch), 1 relay output and a 10M/100M Ethernet RJ45 port can be compatible for correspondence of TCP/IP communication. It can connect 2 Wiegand RFID card readers interface to computer via TCP/IP network. And also can send card numbers from computer to access controller Wiegand input interface by Wiegand 26bit, 34bit, 66bit or other Wiegand bit depend on each project request. The controller working on DC9V to DC24V wide power supply, and also provide a TTL communication interface for testing and upgrade purpose. Consider its cheap price and good quality, it is really a good IOT Wiegand control device for access control.

Product Features:

Using high quality electronic integrated module, Provide good electrical properties.

Support 2 channel Wiegand input and output

Support 2 channel dry contact electric input

Support 1 push button

Provide 1 channel of relay output

Working power: DC9V to DC24V.

Restore factory default

Upgrade firmware via TTL network

Work mode: TCP Server, TCP Client, UDP Client, UDP Server, HTTPD Client

Across the gateway, switches, routers

Can work in LAN, also can work in the Internet (external network)

Support various LED to indicate work status

Guarantee reliable data transmission and long working life.

Set software watchdog timer (about 1s for restart) for keep the device working fine.

Support customization

Technical Parameter

Size: 110mm x 76mm x 20mm

Weight: about 50g (PCB board, without steel housing)

Power supply: DC9V to DC24V/1A, suggest DC12V

Static working current: <150mA (DC12V)

Dynamic current: when all relay closed less than 320mA (under DC12V power)

Wiegand interface: support 2CH Wiegand input and output (WG26/34/66 bit)

Input: support 4CH dry contact electric input (provide jump for set high/low level)

Output: 1 channel of relay output

Communication interface: 10M/100M RJ45 Ethernet and UART-TTL

Baud rate: 9600BPS (default, can set by software)

Address ID: none (defaults ID none, can set by command, range: 1 to 255)

Indicator: LED indicator for power, TCP/IP communication and Wiegand communication

Reset button: press it about 3s for return to factory settings (after 4CH input LED bright red reset ok)

Ethernet module: USR-K2 (default)

Network protocol: support Ethernet, ARP, IP, UDP, TCP, etc.

Ethernet user name: admin, Password: admin, Default IP: 192.168.0.7

Network mode: TCP client\server (max for 4 Clients), UDP Client\Server, HTTDP Client

TTL interface: DC5V, TX, RX, GND, design for testing and upgrade firmware.

Operating Temperature:-40-85 C (-40-185 F)

Storage Temperature:-40～85 °C（-40～185 °F）

Relative humidity: 5%-95% (no condensation)

Software watchdog timers: about 1s restart.

Average fault-free time: 100000 hours

Application field of WST-TCP2WG12

Security access control, parking management, time attendance

Industrial automation, motor control, light power control system

Security and protection monitoring for area

Smart home, power control, environmental monitoring, intelligent agriculture

Automatic payment, POS system, rice selling system

Appearance and connection:

We provide two types of power supply interface, one of plug-in power jack, and another power supply terminal along with 2 channel input interface with1 button push interface; we also provide two types of communication interface, one of RJ45 Ethernet interface for TCP/IP communication, and another white color 4 PIN interface for UART TTL communication. 1 channel of relay output, 2 channels of Wiegand interface, and 2 channels of input interface with 1 button push connection please refer to the above picture.

And here is the connection definition:

1CH relay output: NC COM NO

WG1: VCC D0 D1 GND

WG2: VCC D0 D1 GND

Power jumper: ON (provide power to Wiegand), OFF (no power to Wiegand/WG1/2 need extra power supply)

TTL: 5V TX RX GND

H/L level jumper: H: high level input active (PW+IN), L: low level input active (GND+IN)

Input interface: PW IN2 IN1 PB1 PB0 GND

10M/100M RJ45 Ethernet interface: